描述：
EASY SEAL 混凝土着色剂/密封剂是一种装饰性、溶剂型、渗透性着色剂和透明着色剂/密封剂，表面光泽度低。旨在使新旧混凝土表面焕然一新、重新着色和密封。它有助于消除不均匀的基材吸收，并可作为混凝土表面（如新倾斜板）的底漆。
特性：
EASY SEAL 混凝土着色剂/密封剂干燥速度快，可保护表面免受污渍侵害。具有良好的抗汽车轮胎痕迹能力，可减少白华。具有良好的抗紫外线能力，提供有色和透明两种选择，使用着色底漆和着色包可产生彩色着色剂。
对于车库地板应用，通常不建议使用 EASY SEAL。这是因为光滑无孔的钢抹刀表面。即使经过酸蚀处理，密封剂的渗透性也可能有限，并且可能导致密封剂/染色剂停留在表面顶部，并且当带有湿热轮胎的车辆在表面停放一段时间时，密封剂/染色剂偶尔会脱落。注意：EASY SEAL 混凝土染色剂/密封剂不适用于工厂釉面陶土砖。
主要用途：
用于恢复活力、保护表面免受污渍、重新着色和密封新旧混凝土表面，如车道、小路、露骨料、石板、混凝土铺路砖和类似的砖石表面。EASY SEAL CONCRETE 染色剂/密封剂也可用作倾斜板、脱模混凝土和新混凝土表面的粘合底漆。
准备和应用数据：
表面准备：所有表面：必须完好、清洁、干燥，且无污垢、油、油脂、霉菌、苔藓、烟灰、盐、白华（白盐）和其他污染物。
未涂层、无孔表面（例如钢抹光饰面 - 未涂层）需要酸蚀以帮助 MASTERMAX Prep Etch 渗透。
如果有霉菌或苔藓，请提前用专有杀菌产品对表面进行预处理，并放置至少 2 周，然后通过刮擦或擦洗去除死皮和污垢。待其干燥。
EASY SEAL CONCRETE STAIN/SEALER 的关键是“它必须能够像染色剂/密封剂一样渗透到表面”，使其能够锁定在混凝土上，同时仍然显示表面纹理。
先前密封的表面的准备
所有密封的表面都需要清洁和喷水，以清除任何会阻止密封剂渗透/粘附的表面浮浆和污垢。
脱模混凝土和倾斜板表面：
在使用 EASY SEAL CONCRETE STAIN/SEALER 之前，必须让新鲜混凝土固化至少 28 天。
涂抹 EASY SEAL CONCRETE STAIN/SEALER 之前，必须用清洁剂清洗去除脱模剂，并且表面不得出现防水迹象。
在涂任何面漆之前，先用无气喷涂机、刷子或滚筒涂一层 EASY SEAL CONCRETE STAIN/SEALER。建议在使用 Easy Seal Prep Wash & Thinner 之前将第一层稀释 20%。
如果需要透明釉面，则可能需要在多孔表面上涂最多三层才能获得均匀的光泽。
适用于所有表面：
表面和天气条件：在晴天施工。如果预测 24 小时内有雨或气温低于 10°c 或高于 35°C，则避免施工。如果表面潮湿，施工前应让其干燥 2-3 天（干燥时间取决于表面和条件）。
注意：如果表面潮湿或在使用过程中可能变湿，则不得使用产品，因为可能会遇到密封剂变白的情况。
EASY SEAL 混凝土着色剂/密封剂，直接从罐中取出
EASY SEAL 混凝土着色剂/密封剂，直接从罐中取出
Application Tools:
Application by brush or broom (house type synthetic) is preferred. Airless spray gun. Roller (short nap pile 4-6mm) for use on smooth surfaces.
Applying Stain: Apply the product as mixed directly from the pail (or from either a suitable container for solvent) using the mixing tables for the relevant age or type of substrate. Ideally, apply using a brush or broom (house type synthetic) so you “work" the sealer into the surface to assist with penetration. If applying with a roller, take care to avoid over-rolling and only apply thin coats as excessive amounts of sealer can leave roller marks due to the fast-drying nature of the product, over-rolling or if the surface is too hot during application can give a cobweb effect.
Stir thoroughly to ensure uniformity by using a “bottom to top” mixing action before application. For the coloured stains stir contents until you get a uniform colour mix, check by doing a visual test on the stirring equipment. The coloured sealer needs to be stirred regularly (approximately every 5 minutes) to ensure uniformity of colour throughout the sealing process. It is advisable to pre-mix enough sealer for each coat to ensure uniformity of colour or at least ensure you have the same batch of tinter.
Number of coats:
We recommend two coats following the application table recommendation for the substrate. Additional coats can cause surfaces to be slippery. To avoid slip hazards the addition of 50 g/L of AP Non-slip Additive may be required for a glaze finish on smooth walk-on surfaces.
Drying time & recoating:
EASY SEAL CONCRETE STAIN/SEALER will be touch dry in approximately 30 minutes and can be recoated after 2 hours. Avoid foot traffic for 4 hours and vehicle traffic for 48 hours. Note: Drying times will vary depending on temperature and humidity conditions at the time of application.
Using Tinters:
Add the entire contents of the EASY SEAL Tint Pack colour to the EASY SEAL CONCRETE STAIN/SEALER Tint Base to achieve full colour. Stir thoroughly to ensure uniformity by using a "bottom to top” mixing action. Then check by doing a visual test on the stirring equipment. The coloured sealer needs to be stirred regularly (approximately every 5 minutes) to ensure uniformity of colour throughout the sealing process. It is advisable to pre-mix enough sealer for each coot to ensure uniformity of colour or at least ensure you have the same batch of tinter. Add the entire pack for full colour.
The recommended addition ratios are:
5 litre EASY SEAL CONCRETE STAIN/SEALER Tint Base + 1 x Small EASY SEAL Tint Pack
10 litre EASY SEAL CONCRETE STAIN/SEALER Tint Base + 1 x Medium EASY SEAL Tint Pack
20 litre EASY SEAL CONCRETE STAIN/SEALER Tint Base + 1 x Large EASY SEAL Tint Pack
For variations on the full-strength colour options, please refer to supplier. Do not add more than the recommended amounts as it may impact on sealer performance.
EASY SEAL Tint Pack tinter is not to be used alone and should only be mixed with the
EASY SEAL CONCRETE STAIN/SEALER Tint Base Sealer only.
Maintenance coat: We recommend a maintenance coat before two years to enhance longevity, however this is subject to the personal choice, traffic usage as well as the conditions it may be exposed to.
Thinning:
EASY SEAL Prep Wash & Thinner.
Solvent Washing:
Use EASY SEAL Prep Wash & Thinner. Refer to Tech Data "ESSW1" Solvent Washing.
Clean-up:
EASY SEAL Prep Wash & Thinner or universal thinner.
Note: Do not leave rags or cleaning fabrics.
Protect Our Environment – When disposing of leftover liquid, keep out of stormwater drains and waterways. Take to a local hazardous waste disposal station. Dry all empty containers in a wellventilated area. Dispose of the empty containers according to your local council regulations.
